FVT/FVR-2000-A-D-DVI with RGB-HV, UXGA & Component Video, DVI Single & Dual Link, Stereo Audio & Data Fiber Transport

Features:

• Fully uncompressed up to 1900 x 1200
• Supports: DVI-I, DVI-DL, RGB-HV, DVI-D, WQXGA, 2560×1600
• Optionally supports: SMPTE 292M 1.5G HD, SMPTE 424M 3G HD
• Eq’s and re-clocks
• 4.25 Gb/sec bandwidth
• Loop-thru DVI-I input
• Dual DVI-I outputs
• EOS-4000 Supported
• 2 analog audio
• 1 Data (RS232/422/485)
• Non-reduced blanking for CRT & LCD support
• EDID support
• 1 or 2 fiber
• ST or LC – Multi Mode or Single Mode
• Throw-down or rack

Applications:

• Commodity and stock exchanges
• Medical and MRI displays
• Digital signage
• Sporting and concert displays/scoreboards
• Digital cinema
• Air traffic Control
• Military info displays

Overview:

The VidOptic FVT/FVR-2000-A-D-DVI is a long–haul fiber optic transport solution for high–quality RGB–HV and DVI–D with a DVI–I interface. Ideal for keeping video and audio communications secure in Command and Control facilities, the VidOptic FVT/FVR-2000-A-D-DVI Single Link supports up to 1920×1200 and the Dual Link up to 2560×1600 resolution over a single fiber, and has optional stereo audio and bi–directional data for monitor control.The VidOptic FVT/FVR-2000-A-D-DVI transports a pixel–for–pixel image that is 100% transparent with no frame dropping up to WUXGA, 1920×1200, and enables 100% 24–bits for all scan rates with no contouring or bit reduction at a high scan rate.

The VidOptic FVT/FVR-2000-A-D-DVI system is a convenient single–fiber solution. It has been designed to increase the transmission distance limitations of high resolution RGB and DVI video and computer graphics. The system will transport virtually any VESA–compliant DVI or RGB signal from 640×480 VGA up to and including 1920 x1200 @ 60Hz Reduced Blanking WUXGA or, with the dual link option, 2560 x 1600 WQXGA, as well as HDTV formats from 480P up to and including 1080P.

The VidOptic FVT/FVR-2000-A-D-DVI also supports HDTV and non–RGB video formats such as YUV, YCrCb or YPrPb. The VidOptic FVT/FVR-2000-A-D-DVI has built in re-clocking of the DVI signal to eliminate jitter. EDID data can be obtained from a local monitor connected to the loop thru port, a built in PROM, or, from a monitor connected to the receiver.

The VidOptic FVT/FVR-2000-A-D-DVI also supports the transport of 2 audio channels (one stereo pair) and unidirectional or bidirectional RS232, 422 or 485 type data. The audio path is intended not only for line–level audio such as might be obtained from a computer sound card, but for professional 600 ohm balanced audio applications as well. No additional fibers are required for the audio or data, although 2 fibers are required for bi–directional data and remote EDID options.

The VidOptic FVT/FVR-2000-A-D-DVI  supports operation and setup via the front panel switches (hardware mode) or a software GUI (GUI mode). Most functions are automatic and should not require front panel switch setup. Firmware updates may also be applied via the USB port. If your signal is 1080p, the resulting transport stream is a SMPTE 424M video signal that can be received with an 3G capable optical receiver. When the signal is not 1080p, the resulting signal is a 3G SMPTE 348M SDTI data stream (3G mode) that will pass through a 3G infrastucture but, since it is not video, is not viewable.